Because I've prepared properly, the first take is often the one I end up editing and sending to my client. The second is simply there as a safety net, in case I need to replace any mistakes while editing. It's much better to capture such drop‑ins during the same session as the main performance, as you can be sure that the mic will be in the same place and your voice will have a similar character in both takes.
In late 2009, my wife Simone received an email from Prague in the Czech Republic. The sender, Mirek Jirku, was heading up a project to record voice messages for the foreign‑language versions of the latest Avast! anti‑virus software. Mirek sent us eight messages to be recorded, specified the fee and deadline, and requested a slow, friendly read. He asked us to send separate stereo MP3 files (at 160kbps or higher quality) for each message, specified that we'd have to sign a non‑disclosure agreement before recording, that we'd need to invoice afterwards, and that he'd pay via a wire transfer instead of PayPal (which is often used for international payments).

I use the Adobe Audition package to edit my own voiceover work, but the techniques described below can be used in most audio‑editing software. Start by saving a new version of your original recording. (I keep the name of the file the same, but change the extension from _original to _edit.) Next, I'll turn my attention to the end of the recording, where I stepped away from the mic after the second take and recorded about 10 seconds of silence. Although processing is usually kept to a minimum, dealing with sibilance is important, and Eiosis' De‑esser plug‑in is much more precise than most.Wearing headphones, I can zoom in on this 'silence', turn up the volume, and listen for any background noise. If I notice any constant noise seeping into the recording, I may consider using Adobe Audition's noise‑reduction tool to capture a one‑ or two‑second profile of the silence, and then reduce the offending noise by about 75 percent throughout the recording. I should stress that this is rarely needed, and it's always a last resort, because such processing can generate swirly, metallic artifacts that draw more attention to themselves than the noise you intended to eliminate! But it's good to listen for such issues with fresh ears at the start of your editing session. If you find yourself using noise‑reduction often, that's a sign that you should find a better place to record, or improve the isolation of the space you've chosen. Don't forget that there are other ways to deal with some noise: often, a high‑pass filter is all you will need to clean up a recording, for example. Also remember that if your recording is to be mixed with music, slight background noise won't be noticeable, and that the more exposed your voice in the end product, the more problematic noise will become.

First of all, don’t be put off by the word technical. The ‘technical’ skills you need to learn to involve how you record and then edit your recording and of course you will need a home studio to do this. This needn’t be a daunting prospect though. Many freelance sound engineers are available who can help you with this – contact us if you want a reputable one.
First, I like to listen to the entire voice over recording from start to finish. I may make notes here and there to remind myself of something I want to go back and edit, but this time through I really just want to concentrate on the overall pacing and tone of the recording. Does it sound like I hoped? Did I rush or speak too slowly? Did I flub any words, mumble, or misspeak? Are there weird silences or unknown sounds?
I use the Adobe Audition package to edit my own voiceover work, but the techniques described below can be used in most audio‑editing software. Start by saving a new version of your original recording. (I keep the name of the file the same, but change the extension from _original to _edit.) Next, I'll turn my attention to the end of the recording, where I stepped away from the mic after the second take and recorded about 10 seconds of silence. Although processing is usually kept to a minimum, dealing with sibilance is important, and Eiosis' De‑esser plug‑in is much more precise than most.Wearing headphones, I can zoom in on this 'silence', turn up the volume, and listen for any background noise. If I notice any constant noise seeping into the recording, I may consider using Adobe Audition's noise‑reduction tool to capture a one‑ or two‑second profile of the silence, and then reduce the offending noise by about 75 percent throughout the recording. I should stress that this is rarely needed, and it's always a last resort, because such processing can generate swirly, metallic artifacts that draw more attention to themselves than the noise you intended to eliminate! But it's good to listen for such issues with fresh ears at the start of your editing session. If you find yourself using noise‑reduction often, that's a sign that you should find a better place to record, or improve the isolation of the space you've chosen. Don't forget that there are other ways to deal with some noise: often, a high‑pass filter is all you will need to clean up a recording, for example. Also remember that if your recording is to be mixed with music, slight background noise won't be noticeable, and that the more exposed your voice in the end product, the more problematic noise will become.

As the engineer, your key job is to select and set up the recording space, choose and position the microphone, set levels and make sure you're recording a good, clean signal at a healthy level. Like music, the louder the signal you want to record, the less audible the noise floor, but you don't want to have to speak louder than sounds natural, and you don't want to overcook things when tracking: any distortion will be very noticeable on an exposed voice part, and an otherwise great take with digital clipping won't be acceptable. If you notice clipping only when you start editing, software clip restoration tools might help to make the take usable, but it's not going to be perfect. Remember that although you may have needed to record 'hot' on analogue tape and older 16‑bit digital recording systems, modern 24‑bit A‑D converters can accommodate a much wider dynamic range, so you no longer have to track so loud: you can leave much more headroom.
The quality of your voice over depends almost entirely o the skill of the voice actor you use. A good voice actor will have perfect enunciation (ie, be very easy to understand), speak at an ideal pace (not too fast and not too slow), and have a pleasing voice. They should also be good at acting, and able to convey the feeling or emotions required by the script, using vocal variance and tone to keep the words interesting while also embodying the desired mood.
Finally, as you complete more work, you can end up with a lot of different files from your projects, so good 'housekeeping' of your sessions and recordings is a must. Glancing at the filename simone_kliass_avast_virus_database_neumann_tlm_103_original.wav, I can easily tell that this is the original recording of my wife's "Your virus database has been updated” message in Portuguese for Avast! on a Neumann TLM103 mic. It doesn't matter what your system is, as long as it works and you can stick to it.
Like pacing, vocal tone and inflection refer to ensuring you speak in a natural and pleasant manner. You want to be friendly and engaging, but not so much that you sound fake. No one wants to sound like a game show host. But, you also want to avoid monotone robot voice which, like pacing that’s too slow, can be boring and off-putting for listeners.
I thought keeping recording levels in daw to -12 was reccomended I saw when doing voice overs I saw somewhere on youtube? Is -18 or -15 a better volume to keep it at when recording voice overs? I use an external preamp then going into my audio interface. I always thought it is better not to add amplify on the daw but to do as much as possible to get that clean gain from your audio interface and or preamp. In general when doing reads is -18 really a good level to record voice overs and just leave it at that when done or should you amplify it afterwards? If this is right maybe I should start recording in -18 or at very least -15 in the daw software?
A demo recording of you doing voice-over work is your CV and your business card combined. If you're applying for a voice-over job, you can send the potential customer your demo via the Internet. Ideally you have multiple demos for different types of gigs. For commercials, clients want to hear 60 to 90 seconds of voice work. If you're auditioning as an audiobook reader, five minutes of demo proves that you can stay in character over a longer stretch of time. 
×