ADR / Automated Dialogue Replacement in Salt Lake City, Utah Audio Mixing / Sound Recording Equipment Rentals in Salt Lake City, Utah Audio Mixing / Sweetening / Sound Editing / Sound Designers in Salt Lake City, Utah Audio Technicians / Audio Engineer / A1 / A2 in Salt Lake City, Utah Film Post Production Services in Salt Lake City, Utah Foley Stages in Salt Lake City, Utah Post House / Video Post Production Facilities / Editing Services in Salt Lake City, Utah Recording Studios in Salt Lake City, Utah Sound Mixers / Recordists in Salt Lake City, Utah Voice Over Artists in Salt Lake City, Utah
We screen our talents to make sure your voice recording has a professional broadcast quality level. Once you order a project, your money is absolutely safe with us. We do not pay the voiceover artist until the project is successfully done and approved by you. You can asks for revisions at no extra cost as long as they don't involve changes in the script.
You need to appreciate that there is a lot to learn and do before your first paid voice acting job. Yes, you want to get out there and start auditioning. But first, you’re going to need proper training, equipment, resources, and yes, some natural talent. The great news is that even though the voice over industry is competitive, there is plenty of voice over work out there for everyone. This guide on how to become a voice actor will give you a good idea of where to start.
Also listen for sibilance. Strong 'ess' sounds are best corrected at source, by using good mic technique, but sometimes they're unavoidable. If you hear an 'ess' that really sizzles in your recording, you can manually reduce its volume. You can, of course, also use a de‑esser, but do be careful, as applying some de‑essers to the entire audio file can alter the sound of your recording. It often works best to apply them to short sections, either offline or using automation. My preferred de‑esser plug‑in is the one sold by Eiosis (www.eiosis.com),Make sure you record some silence at the end of each take. That way, if a great performance suffers from noise issues, you have something to feed your noise‑reduction processors. Just don't rely on this technique too much! which cleverly separates the esses from the rest of the audio and allows you to manipulate them independently. If you want to learn about some more advanced strategies for de‑essing check out Mike Senior's article from SOS May 2009 (/sos/may09/articles/deessing.htm).
Hey Rob. You certainly know your stuff. I know this for a fact, because I’ve been a working professional at this for nearly ten years and spend every week since that time making mistakes and learning from them. I also incorporate 99 percent of your suggestions here and believe it folks they work, if used properly. Very informative and practical. Thanks, Rob.
2. You need training. “Winging it” isn’t professional because it’s unreliable, and could explain why there are so many one-hit wonders in this profession. You need a professional approach, mic technique training, and time dedicated to practice, practice, practice in order to build your skills. Your confidence will build from there. Much like circuit training fine tunes your physical acuity with continued use, technique training conditions your performance muscle. You can’t expect to run a marathon if you don’t train. Every skill level of talent benefits from proper coaching.
As I've mentioned, most of our clients prefer to do post‑production work themselves, and request the raw (but edited) recordings. Sometimes, though, as in the Avast! job, the client will want the files ready to go, which might mean using slight EQ and compression. The noise floor on my recordings generally hovers around ‑54dB, but by using EQ to roll off frequencies below 80Hz and above 12kHz, I am usually able to lower the noise floor to around ‑57dB without resorting to noise reduction. Using EQ to reduce low‑end rumble and high‑frequency noise will make your recording sound better, and will be particularly beneficial if you'll be adding compression later, as the compressor's make-up gain won't be raising the level of that noise. Used moderately, compression can usefully reduce dynamic range, and thus improve intelligibility of the words, while still leaving you with a natural‑sounding result. Used excessively, it will suck the life out of a recording.
Some of you might be wondering about the difference between voice over and narration. The short answer: not much. In most cases, you may use voice over and narration fairly interchangeably. However, to be technically correct, narration typically refers to an audio vocal that describes all the action on screen or tells a story based on what’s happening, while voice over may or may not describe as much action and is often more instructional in nature.
So, how do you get started? Like all things acting, voiceover can appear elusive at the onset, if not downright secretive. In part because your experience, or lack thereof, leaves you vulnerable to assumptions, hearsay, and clichés such as, “The same 10 people get all the work,” which is literally impossible—especially when you consider the average American hears approximately 9,000 voiceovers a day. And, according to one study, the demand for professional voiceover talent, otherwise known as a vocal brand, has increased by more than 2000 percent since 2009.
A better, more natural-sounding way to clean up a voice recording, though, is to paste in strips of 'silence' that showcase your home studio at its best. To do this, wake up early (ie. when your house is quiet), turn on your gear and set your levels for a normal job. Then record a full minute of silence at whatever bit depths and sample rates you're likely to be using. Repeat this process for each different mic you use, and save each file in a folder titled Room Tones, or something similarly suitable.
As the engineer, your key job is to select and set up the recording space, choose and position the microphone, set levels and make sure you're recording a good, clean signal at a healthy level. Like music, the louder the signal you want to record, the less audible the noise floor, but you don't want to have to speak louder than sounds natural, and you don't want to overcook things when tracking: any distortion will be very noticeable on an exposed voice part, and an otherwise great take with digital clipping won't be acceptable. If you notice clipping only when you start editing, software clip restoration tools might help to make the take usable, but it's not going to be perfect. Remember that although you may have needed to record 'hot' on analogue tape and older 16‑bit digital recording systems, modern 24‑bit A‑D converters can accommodate a much wider dynamic range, so you no longer have to track so loud: you can leave much more headroom.