Some of you might be wondering about the difference between voice over and narration. The short answer: not much. In most cases, you may use voice over and narration fairly interchangeably. However, to be technically correct, narration typically refers to an audio vocal that describes all the action on screen or tells a story based on what’s happening, while voice over may or may not describe as much action and is often more instructional in nature.

"Ideally the talent should be seated, staying on axis, approximately a foot away from the mic, which should be angled back from the face a bit, not parallel to it. You'll need to see what angle provides the best results, usually a few degrees off from parallel works great — and located between the forehead and the nose, not directly in line with the mouth. This will help with plosives, mouth noise, and some other issues. Movement in the booth should be limited, as the microphone is likely to pick up arms flailing, hands rubbing, page turns, stomach growling, and so on. Keep the levels consistent, moving closer if the scene calls for a whisper, or moving back for a loud voice or scream. A well‑versed narrator is capable of delivering a dynamic performance without creating dynamic levels.”


As the engineer, your key job is to select and set up the recording space, choose and position the microphone, set levels and make sure you're recording a good, clean signal at a healthy level. Like music, the louder the signal you want to record, the less audible the noise floor, but you don't want to have to speak louder than sounds natural, and you don't want to overcook things when tracking: any distortion will be very noticeable on an exposed voice part, and an otherwise great take with digital clipping won't be acceptable. If you notice clipping only when you start editing, software clip restoration tools might help to make the take usable, but it's not going to be perfect. Remember that although you may have needed to record 'hot' on analogue tape and older 16‑bit digital recording systems, modern 24‑bit A‑D converters can accommodate a much wider dynamic range, so you no longer have to track so loud: you can leave much more headroom. 

Part of great voice over work is ensuring that you pronounce each word correctly and that you speak clearly enough to be understood. Avoid mumbling but don’t shout or over-enunciate, either. Don’t worry, though. No one expects you to sound like a professional voice actor. The best thing you can do is speak naturally and clearly and the rest will follow in time.
First of all, don’t be put off by the word technical. The ‘technical’ skills you need to learn to involve how you record and then edit your recording and of course you will need a home studio to do this. This needn’t be a daunting prospect though. Many freelance sound engineers are available who can help you with this – contact us if you want a reputable one.
As the engineer, your key job is to select and set up the recording space, choose and position the microphone, set levels and make sure you're recording a good, clean signal at a healthy level. Like music, the louder the signal you want to record, the less audible the noise floor, but you don't want to have to speak louder than sounds natural, and you don't want to overcook things when tracking: any distortion will be very noticeable on an exposed voice part, and an otherwise great take with digital clipping won't be acceptable. If you notice clipping only when you start editing, software clip restoration tools might help to make the take usable, but it's not going to be perfect. Remember that although you may have needed to record 'hot' on analogue tape and older 16‑bit digital recording systems, modern 24‑bit A‑D converters can accommodate a much wider dynamic range, so you no longer have to track so loud: you can leave much more headroom.
Congratulations! You should now have a finished voiceover recording. Save a final copy with the extension _master and use this version to save another copy in the format requested by the client. But don't think your job is done when you hand everything back to your producer‑self. Running a profitable home‑based voiceover business takes more than building and equipping a home studio and recording and editing audio files. You still have to design a web site, launch a marketing campaign, and secure new clients — all of which is something we'll look at another time.  
You don't need a state-of-the-art production studio to work in voice-over. You do need good enough equipment to record, edit and submit a good audition. A computer with a microphone and a mixer may do the trick. It's important that the room you record in be as soundproof as possible – if you use a walk-in closet where the clothes muffle the sounds outside, the industry's not going to complain.
You will never have to answer to a “boss”, but you will need to be your own boss and manage yourself. You will work on your own a lot of the time. So you need to embrace the benefits and the challenges this presents. Take courses in areas where you need to develop your skills. When you adequately prepare for running a business, you will succeed in its management, even if part of managing your business means hiring out, in areas that you know are not your strongest.
"This was Alfre Woodard's audiobook directing debut, and she pulled an amazing performance from people. The big [thing] was to remember that these stories were being told in intimate settings, one‑on‑one in most cases, so the talent really needed to speak to the individual listener. An image kept in mind was stories being told around a campfire, back when folktales were passed down by spoken word.”

In other words, Mirek gave us all the information we needed to start the job. Unfortunately, though, that's not how it usually works! Usually, you'll need to work hard to get all the information you need from your client to do the job well. If you're at all uncertain about their expectations, whether about the performance, or about technical and organisational issues such as file formats or payment procedures, save yourself time and a headache by clearing up all doubts beforehand, and don't hit the record button until your client has given you the green light by email. With that sorted, you can more easily don your other hats and get on with the job.
First of all let’s dismiss the obvious – there is no such thing as a standard rate, there are only guide lines and even these vary by Country and type of work. The only standard rates are those set by some Union scale rates. One of the most notable differences is that between voice over union rates and voice over rates non-union. Unions provide a standard voiceover rate and therefore you can safely rely on the unions guide (depending on which Country you are in). However, non union voice over rates vary enormously and are often down to negotiations between the voice over actor and the client.
When you come to actually recording your voice, try to think of the mic as the ear of your listener. Picture your listener, have an opinion, and read the script as if the words were coming to mind that instant. The distance between your mouth and the mic should be about the same as the distance between your thumb and pinkie when making a hang‑five gesture (see the picture above). Move closer to the mic when you lower your voice and back off when you speak louder. On‑line dictionaries such as the Merriam‑Webster one pictured here, often include audio examples which can help you clarify pronunciation. Just make sure that you use an American English or UK English (or other language!) version as appropriate. (Remember, while you have your engineer hat on, to take account of this when setting levels.) Always use a pop shield, and I'd suggest trying to work slightly off‑axis, as talking to a point just to the right or left of the mic will prevent bursts of air and drops of saliva ruining your recording. I'd also recommend wearing headphones over one ear only, as this allows you to judge volume and listen for clipping and plosives on the recording, while also hearing your natural voice, which makes it easier to focus on that message we talked about. Simone demonstrates this technique in the picture on the next page. Hhe's working slightly off‑axis and has backed off an inch or two to deliver with more energy.Typically, you'd record with your mouth approximately the distance between your thumb and little finger from the mic, as pictured here.
“Bunny Studio Voice is an indispensable part of my production workflow. Using them saves me time and money compared to hiring a recording studio and VO artist. Without a doubt, their best feature is customer service. Thanks to their enormous support, I have saved DAYS off my deadlines and received pitch-perfect reads. I couldn’t recommend them more”

© 2020 GoAnimate, Inc. All Rights Reserved. VYOND™ is a trademark of GoAnimate, Inc., registered in Australia, Brazil, Chile, the European Union, Hong Kong, India, Israel, Mexico, New Zealand, Norway, OAPI, the Philippines, Singapore, Switzerland, the United Kingdom, and Vietnam; Reg. U.S. Pat. & Tm. Off. Other names and marks are the property of their respective holders.


I use the Adobe Audition package to edit my own voiceover work, but the techniques described below can be used in most audio‑editing software. Start by saving a new version of your original recording. (I keep the name of the file the same, but change the extension from _original to _edit.) Next, I'll turn my attention to the end of the recording, where I stepped away from the mic after the second take and recorded about 10 seconds of silence. Although processing is usually kept to a minimum, dealing with sibilance is important, and Eiosis' De‑esser plug‑in is much more precise than most.Wearing headphones, I can zoom in on this 'silence', turn up the volume, and listen for any background noise. If I notice any constant noise seeping into the recording, I may consider using Adobe Audition's noise‑reduction tool to capture a one‑ or two‑second profile of the silence, and then reduce the offending noise by about 75 percent throughout the recording. I should stress that this is rarely needed, and it's always a last resort, because such processing can generate swirly, metallic artifacts that draw more attention to themselves than the noise you intended to eliminate! But it's good to listen for such issues with fresh ears at the start of your editing session. If you find yourself using noise‑reduction often, that's a sign that you should find a better place to record, or improve the isolation of the space you've chosen. Don't forget that there are other ways to deal with some noise: often, a high‑pass filter is all you will need to clean up a recording, for example. Also remember that if your recording is to be mixed with music, slight background noise won't be noticeable, and that the more exposed your voice in the end product, the more problematic noise will become.
Keep it respectable and charge what your time and services are worth. That means establishing some minimums. For example, you might set a minimum price of $100 per job. So if the client says they can get it done locally for less than half that price, you explain that they are getting a professional recording and the difference is in the quality of the recording.
Next, run these files through any standard EQ high‑pass and low‑pass filters you use, zoom in on the waveform, and select a one‑second strip of silence from each recording. Save these strips as separate files. For instance, on my system, a one‑second strip of silence recorded at 16‑bit, 44.1kHz on a Neumann TLM103 would have this name: room_tone_neumann_tlm_103_44100_16_one_second.wav. Ideally, the noise floor of each strip will be lower than ‑60dB. Now, when you have to remove a bump or a squeak between words, you can paste in a piece of these strips instead of muting, which would draw attention to the edit.
Union and non-union jobs have always been two separate markets. Non-union work is more visible and attractive today when compared to years ago, due to online casting. The availability of professional talent for non-union work has led to a reshaping of the voice over industry. An open market means that each professional voice actor sets their own rate based on what they need to cover.
No place is totally silent, so find the best place you can — even if that means thinking outside the box. I have a friend who regularly records his podcast in his car. He lives in a small house with dogs and kids, so there really isn’t anywhere else quiet enough. He takes his laptop and mic out to his driveway, shuts himself in the car and records. The results are surprisingly good!
It’s equally important to realize that when you join a union, you pledge to no longer accept non-union work. The reason for this is solidarity: you stand together with your fellow members so that you can negotiate better working conditions and pay for all of you as a collective. It’s worth noting, however, that a union in any given country only functions within the borders of that country and not beyond them.
Voiceover-Services.com welcomes you to listen & consider professional voice actor Paul Fraley for your next campaign or project. Located in Los Angeles, Paul brings an excitement & unique point-of-view to his work. Whether voicing National TV commercials, explainer videos, creating character voices for international video game apps or as the signature voice for a mid-west grocery store chain – Paul always looks forward to telling the next story.
While having a broad set of voice skills is beneficial, many voice overs establish themselves in commercials and more general corporate voiceover work before specialising. Having a niche or specialist focus though can make a difference in earning potential. So, bearing in mind the question: how much money do a voice actors make, will also depend on the level and experience in a given niche e.g. animation, audiobooks or gaming.
Why the difference in approach? Lots of my e‑learning and corporate jobs are done for production houses that will be adding other voices to the mix. Ironically, if I record my voice via a great mic and preamp, and add some nice processing, it can end up standing out from the other voices, drawing attention to itself. The production house will see this as me causing them a problem, even though my recording sounds better than the others!
When you come to actually recording your voice, try to think of the mic as the ear of your listener. Picture your listener, have an opinion, and read the script as if the words were coming to mind that instant. The distance between your mouth and the mic should be about the same as the distance between your thumb and pinkie when making a hang‑five gesture (see the picture above). Move closer to the mic when you lower your voice and back off when you speak louder. On‑line dictionaries such as the Merriam‑Webster one pictured here, often include audio examples which can help you clarify pronunciation. Just make sure that you use an American English or UK English (or other language!) version as appropriate. (Remember, while you have your engineer hat on, to take account of this when setting levels.) Always use a pop shield, and I'd suggest trying to work slightly off‑axis, as talking to a point just to the right or left of the mic will prevent bursts of air and drops of saliva ruining your recording. I'd also recommend wearing headphones over one ear only, as this allows you to judge volume and listen for clipping and plosives on the recording, while also hearing your natural voice, which makes it easier to focus on that message we talked about. Simone demonstrates this technique in the picture on the next page. Hhe's working slightly off‑axis and has backed off an inch or two to deliver with more energy.Typically, you'd record with your mouth approximately the distance between your thumb and little finger from the mic, as pictured here.

3. You need a simple, reliable, home-recording setup. Keep in mind: Your objective is on being the best voice talent you can be, not the best production studio or recording engineer. Nevertheless, you do need the ability to record, edit, and turnaround a proper audition. Do not run out and purchase a mic! You can’t return it, for hygienic reasons. Besides, there’s a bit of a learning curve to this and recent industry advances have made having a home “studio” easier and more affordable than ever before. You could have the best gear and the coolest toys on the block, but if you can’t use them it’s a waste. (Tip: What you’re recording on matters less than where you’re recording. Find a quiet place like a closet full of clothes to record in.)

We screen our talents to make sure your voice recording has a professional broadcast quality level. Once you order a project, your money is absolutely safe with us. We do not pay the voiceover artist until the project is successfully done and approved by you. You can asks for revisions at no extra cost as long as they don't involve changes in the script.
You will never have to answer to a “boss”, but you will need to be your own boss and manage yourself. You will work on your own a lot of the time. So you need to embrace the benefits and the challenges this presents. Take courses in areas where you need to develop your skills. When you adequately prepare for running a business, you will succeed in its management, even if part of managing your business means hiring out, in areas that you know are not your strongest.

Next, go back to the beginning and start editing out your mistakes. I also like to edit out any abnormally long silences between sentences or statements and any weird sounds that don’t belong. Remember, though, that pauses are ok (and even necessary) to help break up the audio and make it feel more natural and conversational, so don’t go hog wild with it.


It's only after this sort of processing that I'll start cleaning up the recording and dealing with the gaps of silence between spoken passages. A noise gate (or an off‑line 'strip‑silence' function) can be used to automatically mute sections that fall below a certain level. However, if not used carefully, these tools will clip the 'T's and 'P's off the ends of words, and shut out natural breathing sounds. Worse, if your recording is noisy, a noise gate will actually draw attention to the problem, since your client will be able to hear the difference between room tone and absolute muting. Another trick is to use a downward expander to reduce the noise floor of quiet sections, rather than cut out the noise completely.

Even if you're mixing yourself, it's better to add EQ and compression only when you can hear how it will sit with the soundtrack or special effects. Ultimately, it comes down to knowing what your voice will be used for and making a judgement. For instance, if I'm recording a tagline for a TV or radio advert, I'll generally run a mic into a nice preamp (where I might add slight tube warmth, and subtle EQ or compression, just to give the recording a bit of 'body'), and I may do a little de‑essing using a plug‑in when performing any edits. However, for e‑learning jobs, corporate videos and so on, I'll tend not to add any creative processing while recording or editing, and will only use the de‑esser ever so slightly.

×