Not all noise can be tackled in this way, though: you need to listen for clicks, plosives, digital glitches and the like. These can normally be acceptably repaired by using a 'heal' tool, or a pencil tool to redraw the waveform. Popped 'p's can often be 'fixed' using a high‑pass filter set at 100Hz. For a single glitch, you can zoom in and cut out the cycle of the waveform in which the glitch appears. Just be careful to start and end the cut where the waveform crosses the centre line, otherwise you'll inadvertently add another digital glitch. If glitches are frequent, it's likely that there's a problem with your audio interface's buffer settings — it may be just a playback issue.
"We recorded two or three takes of each story, and within those takes there were some pick‑ups [overdubs] for certain lines. When I was editing, I used takes that gave the best delivery, had the least movement or other noise, and provided the most provoking images. In some cases [we used] the first take. Sometimes, after saying a line over and over, one starts to lose the meaning of the line. Pick‑ups should go back to the top of the sentence, making editing much easier.”
"You need to be able to pull the listener in, help them suspend disbelief, become a part of the world the author created, and take the journey with your voice as the guide. Practice your character voices; they must be believable and honest. Work on your accents and timing and delivery within different genres. When reading, read out loud — even if you're not recording or being paid for it. This will help you with flow and dialogue. Listen to other audiobooks and figure out what you like and don't like, then work on these factors in your own performances. Working from a home studio, you have many more responsibilities to consider. Be mindful of them, set attainable goals and know your limitations. Never over-promise and under-deliver to a client. There are many established and aspiring narrators out there, so bring your best to the table.”
Always keep it professional. A client may not have a budget that works within your rates presently, but one day they may have a project with a much larger budget and think of you as the talent to circle back to! It never hurts to politely decline when a project has too low of a rate and exclaim, “I would love to work with you in the future when our rates align!”
I thought keeping recording levels in daw to -12 was reccomended I saw when doing voice overs I saw somewhere on youtube? Is -18 or -15 a better volume to keep it at when recording voice overs? I use an external preamp then going into my audio interface. I always thought it is better not to add amplify on the daw but to do as much as possible to get that clean gain from your audio interface and or preamp. In general when doing reads is -18 really a good level to record voice overs and just leave it at that when done or should you amplify it afterwards? If this is right maybe I should start recording in -18 or at very least -15 in the daw software?
It's only after this sort of processing that I'll start cleaning up the recording and dealing with the gaps of silence between spoken passages. A noise gate (or an off‑line 'strip‑silence' function) can be used to automatically mute sections that fall below a certain level. However, if not used carefully, these tools will clip the 'T's and 'P's off the ends of words, and shut out natural breathing sounds. Worse, if your recording is noisy, a noise gate will actually draw attention to the problem, since your client will be able to hear the difference between room tone and absolute muting. Another trick is to use a downward expander to reduce the noise floor of quiet sections, rather than cut out the noise completely.

As the engineer, your key job is to select and set up the recording space, choose and position the microphone, set levels and make sure you're recording a good, clean signal at a healthy level. Like music, the louder the signal you want to record, the less audible the noise floor, but you don't want to have to speak louder than sounds natural, and you don't want to overcook things when tracking: any distortion will be very noticeable on an exposed voice part, and an otherwise great take with digital clipping won't be acceptable. If you notice clipping only when you start editing, software clip restoration tools might help to make the take usable, but it's not going to be perfect. Remember that although you may have needed to record 'hot' on analogue tape and older 16‑bit digital recording systems, modern 24‑bit A‑D converters can accommodate a much wider dynamic range, so you no longer have to track so loud: you can leave much more headroom.

ADR / Automated Dialogue Replacement in Salt Lake City, Utah Audio Mixing / Sound Recording Equipment Rentals in Salt Lake City, Utah Audio Mixing / Sweetening / Sound Editing / Sound Designers in Salt Lake City, Utah Audio Technicians / Audio Engineer / A1 / A2 in Salt Lake City, Utah Film Post Production Services in Salt Lake City, Utah Foley Stages in Salt Lake City, Utah Post House / Video Post Production Facilities / Editing Services in Salt Lake City, Utah Recording Studios in Salt Lake City, Utah Sound Mixers / Recordists in Salt Lake City, Utah Voice Over Artists in Salt Lake City, Utah
Our recommendation is to start small and reinvest the money you make into upgrading your equipment and set up. All clients, whether they are Pixar or just a guy who needs a voicemail message, expect crystal clear audio recordings. You absolutely MUST be recording in a professional recording environment with professional equipment. They are NOT going to settle for less than perfection. Does this mean spending thousands of dollars? Maybe, eventually it does, but not today. What you’ll need to get started: 

When you come to actually recording your voice, try to think of the mic as the ear of your listener. Picture your listener, have an opinion, and read the script as if the words were coming to mind that instant. The distance between your mouth and the mic should be about the same as the distance between your thumb and pinkie when making a hang‑five gesture (see the picture above). Move closer to the mic when you lower your voice and back off when you speak louder. On‑line dictionaries such as the Merriam‑Webster one pictured here, often include audio examples which can help you clarify pronunciation. Just make sure that you use an American English or UK English (or other language!) version as appropriate. (Remember, while you have your engineer hat on, to take account of this when setting levels.) Always use a pop shield, and I'd suggest trying to work slightly off‑axis, as talking to a point just to the right or left of the mic will prevent bursts of air and drops of saliva ruining your recording. I'd also recommend wearing headphones over one ear only, as this allows you to judge volume and listen for clipping and plosives on the recording, while also hearing your natural voice, which makes it easier to focus on that message we talked about. Simone demonstrates this technique in the picture on the next page. Hhe's working slightly off‑axis and has backed off an inch or two to deliver with more energy.Typically, you'd record with your mouth approximately the distance between your thumb and little finger from the mic, as pictured here.
Next, go back to the beginning and start editing out your mistakes. I also like to edit out any abnormally long silences between sentences or statements and any weird sounds that don’t belong. Remember, though, that pauses are ok (and even necessary) to help break up the audio and make it feel more natural and conversational, so don’t go hog wild with it.
As I've mentioned, most of our clients prefer to do post‑production work themselves, and request the raw (but edited) recordings. Sometimes, though, as in the Avast! job, the client will want the files ready to go, which might mean using slight EQ and compression. The noise floor on my recordings generally hovers around ‑54dB, but by using EQ to roll off frequencies below 80Hz and above 12kHz, I am usually able to lower the noise floor to around ‑57dB without resorting to noise reduction. Using EQ to reduce low‑end rumble and high‑frequency noise will make your recording sound better, and will be particularly beneficial if you'll be adding compression later, as the compressor's make-up gain won't be raising the level of that noise. Used moderately, compression can usefully reduce dynamic range, and thus improve intelligibility of the words, while still leaving you with a natural‑sounding result. Used excessively, it will suck the life out of a recording.
No place is totally silent, so find the best place you can — even if that means thinking outside the box. I have a friend who regularly records his podcast in his car. He lives in a small house with dogs and kids, so there really isn’t anywhere else quiet enough. He takes his laptop and mic out to his driveway, shuts himself in the car and records. The results are surprisingly good!
3. You need a simple, reliable, home-recording setup. Keep in mind: Your objective is on being the best voice talent you can be, not the best production studio or recording engineer. Nevertheless, you do need the ability to record, edit, and turnaround a proper audition. Do not run out and purchase a mic! You can’t return it, for hygienic reasons. Besides, there’s a bit of a learning curve to this and recent industry advances have made having a home “studio” easier and more affordable than ever before. You could have the best gear and the coolest toys on the block, but if you can’t use them it’s a waste. (Tip: What you’re recording on matters less than where you’re recording. Find a quiet place like a closet full of clothes to record in.)
Digital Commercials are defined as spots that are used to advertise a product or service that are run on websites or platforms other than the client's own. For example, a 15 second recording that plays on YouTube before the requested content begins. Explainer videos are not included in this rate, they fall into INTERNET USAGE / EXPLAINER in another category.
You start off each job as a producer, consulting your client and getting briefed on the project at hand. Then you become an engineer, dealing with recording gear and software, setting the mic position and levels. Next, you step up to the mic as an actor, bringing the script off the page and connecting with the listener. Meanwhile, the director in you sits behind the metaphorical glass, making sure the actor doesn't mispronounce a word or stumble through a passage of text. Then you're an editor, cleaning up the best take and sending the resulting audio to your client. You need to be able to perform all of these roles to a high standard, and the better you are at each, the more your business will prosper.
Before you get down to the nitty-gritty, though, I recommend doing a test recording to ensure your equipment works properly and your audio levels are strong. You don’t need to record the entire script, but a few paragraphs will give you enough to ensure that the audio is clear, at an appropriate level, and doesn’t include any stray or ambient noises.
No place is totally silent, so find the best place you can — even if that means thinking outside the box. I have a friend who regularly records his podcast in his car. He lives in a small house with dogs and kids, so there really isn’t anywhere else quiet enough. He takes his laptop and mic out to his driveway, shuts himself in the car and records. The results are surprisingly good!
A demo recording of you doing voice-over work is your CV and your business card combined. If you're applying for a voice-over job, you can send the potential customer your demo via the Internet. Ideally you have multiple demos for different types of gigs. For commercials, clients want to hear 60 to 90 seconds of voice work. If you're auditioning as an audiobook reader, five minutes of demo proves that you can stay in character over a longer stretch of time.
"Ideally the talent should be seated, staying on axis, approximately a foot away from the mic, which should be angled back from the face a bit, not parallel to it. You'll need to see what angle provides the best results, usually a few degrees off from parallel works great — and located between the forehead and the nose, not directly in line with the mouth. This will help with plosives, mouth noise, and some other issues. Movement in the booth should be limited, as the microphone is likely to pick up arms flailing, hands rubbing, page turns, stomach growling, and so on. Keep the levels consistent, moving closer if the scene calls for a whisper, or moving back for a loud voice or scream. A well‑versed narrator is capable of delivering a dynamic performance without creating dynamic levels.”
We screen our talents to make sure your voice recording has a professional broadcast quality level. Once you order a project, your money is absolutely safe with us. We do not pay the voiceover artist until the project is successfully done and approved by you. You can asks for revisions at no extra cost as long as they don't involve changes in the script.
You start off each job as a producer, consulting your client and getting briefed on the project at hand. Then you become an engineer, dealing with recording gear and software, setting the mic position and levels. Next, you step up to the mic as an actor, bringing the script off the page and connecting with the listener. Meanwhile, the director in you sits behind the metaphorical glass, making sure the actor doesn't mispronounce a word or stumble through a passage of text. Then you're an editor, cleaning up the best take and sending the resulting audio to your client. You need to be able to perform all of these roles to a high standard, and the better you are at each, the more your business will prosper.
"Ideally the talent should be seated, staying on axis, approximately a foot away from the mic, which should be angled back from the face a bit, not parallel to it. You'll need to see what angle provides the best results, usually a few degrees off from parallel works great — and located between the forehead and the nose, not directly in line with the mouth. This will help with plosives, mouth noise, and some other issues. Movement in the booth should be limited, as the microphone is likely to pick up arms flailing, hands rubbing, page turns, stomach growling, and so on. Keep the levels consistent, moving closer if the scene calls for a whisper, or moving back for a loud voice or scream. A well‑versed narrator is capable of delivering a dynamic performance without creating dynamic levels.”
"You need to be able to pull the listener in, help them suspend disbelief, become a part of the world the author created, and take the journey with your voice as the guide. Practice your character voices; they must be believable and honest. Work on your accents and timing and delivery within different genres. When reading, read out loud — even if you're not recording or being paid for it. This will help you with flow and dialogue. Listen to other audiobooks and figure out what you like and don't like, then work on these factors in your own performances. Working from a home studio, you have many more responsibilities to consider. Be mindful of them, set attainable goals and know your limitations. Never over-promise and under-deliver to a client. There are many established and aspiring narrators out there, so bring your best to the table.”
However, there are lots of second tier voice over agencies and ones that are just getting established. One of your goals as a voice actor should be to get listed by an agency. However, wait until you have at least established yourself and put together a portfolio of work and super hot demos you can send out to them for consideration. When selecting an agent you need to carefully examine who they currently represent and then ask yourself: How do I fit in here? Does this agent have anyone like me on their books? If not, you will most definitely stand a better chance of being represented.
×