When you come to actually recording your voice, try to think of the mic as the ear of your listener. Picture your listener, have an opinion, and read the script as if the words were coming to mind that instant. The distance between your mouth and the mic should be about the same as the distance between your thumb and pinkie when making a hang‑five gesture (see the picture above). Move closer to the mic when you lower your voice and back off when you speak louder. On‑line dictionaries such as the Merriam‑Webster one pictured here, often include audio examples which can help you clarify pronunciation. Just make sure that you use an American English or UK English (or other language!) version as appropriate. (Remember, while you have your engineer hat on, to take account of this when setting levels.) Always use a pop shield, and I'd suggest trying to work slightly off‑axis, as talking to a point just to the right or left of the mic will prevent bursts of air and drops of saliva ruining your recording. I'd also recommend wearing headphones over one ear only, as this allows you to judge volume and listen for clipping and plosives on the recording, while also hearing your natural voice, which makes it easier to focus on that message we talked about. Simone demonstrates this technique in the picture on the next page. Hhe's working slightly off‑axis and has backed off an inch or two to deliver with more energy.Typically, you'd record with your mouth approximately the distance between your thumb and little finger from the mic, as pictured here.

Because I've prepared properly, the first take is often the one I end up editing and sending to my client. The second is simply there as a safety net, in case I need to replace any mistakes while editing. It's much better to capture such drop‑ins during the same session as the main performance, as you can be sure that the mic will be in the same place and your voice will have a similar character in both takes.

Next, run these files through any standard EQ high‑pass and low‑pass filters you use, zoom in on the waveform, and select a one‑second strip of silence from each recording. Save these strips as separate files. For instance, on my system, a one‑second strip of silence recorded at 16‑bit, 44.1kHz on a Neumann TLM103 would have this name: room_tone_neumann_tlm_103_44100_16_one_second.wav. Ideally, the noise floor of each strip will be lower than ‑60dB. Now, when you have to remove a bump or a squeak between words, you can paste in a piece of these strips instead of muting, which would draw attention to the edit.


Digital Commercials are defined as spots that are used to advertise a product or service that are run on websites or platforms other than the client's own. For example, a 15 second recording that plays on YouTube before the requested content begins. Explainer videos are not included in this rate, they fall into INTERNET USAGE / EXPLAINER in another category.
At this point — unless you're tracking for broadcast applications (where they don't work to peak levels) — consider 'normalising' your recording to an optimal level. Normalisation can be used to push the loudest peak to around ‑1dB and increase the volume of the entire recording by the same ratio. Of course, you can also tighten up dynamic range (the difference between the softest and loudest parts of your recording) by manually reducing the loudest sections of the recording before you apply normalisation. On a final note, if you do plan to use a compressor, then you might as well add gain at that stage instead of normalising.
Finally, as you complete more work, you can end up with a lot of different files from your projects, so good 'housekeeping' of your sessions and recordings is a must. Glancing at the filename simone_kliass_avast_virus_database_neumann_tlm_103_original.wav, I can easily tell that this is the original recording of my wife's "Your virus database has been updated” message in Portuguese for Avast! on a Neumann TLM103 mic. It doesn't matter what your system is, as long as it works and you can stick to it.
Because I've prepared properly, the first take is often the one I end up editing and sending to my client. The second is simply there as a safety net, in case I need to replace any mistakes while editing. It's much better to capture such drop‑ins during the same session as the main performance, as you can be sure that the mic will be in the same place and your voice will have a similar character in both takes.
If a client likes your demo, they may invite you to audition. In the 21st century, you can download the audition script, record the audition at home, and then send the results to your client over the Internet. Prepare yourself for a life of constant auditions: Even successful voice pros may do many more auditions than actual jobs. But if enough jobs come your way, it's worth it.
Audio Voiceover in Salt Lake City Voice Over in Salt Lake City Studio in Salt Lake City Recording Studio in Salt Lake City Narration in Salt Lake City ISDN voice in Salt Lake City Voice Recording in Salt Lake City Male Voice in Salt Lake City Female Voice in Salt Lake City Voice Talent in Salt Lake City Recording in Salt Lake City Voiceover Artist in Salt Lake City

Our recommendation is to start small and reinvest the money you make into upgrading your equipment and set up. All clients, whether they are Pixar or just a guy who needs a voicemail message, expect crystal clear audio recordings. You absolutely MUST be recording in a professional recording environment with professional equipment. They are NOT going to settle for less than perfection. Does this mean spending thousands of dollars? Maybe, eventually it does, but not today. What you’ll need to get started:
3. You need a simple, reliable, home-recording setup. Keep in mind: Your objective is on being the best voice talent you can be, not the best production studio or recording engineer. Nevertheless, you do need the ability to record, edit, and turnaround a proper audition. Do not run out and purchase a mic! You can’t return it, for hygienic reasons. Besides, there’s a bit of a learning curve to this and recent industry advances have made having a home “studio” easier and more affordable than ever before. You could have the best gear and the coolest toys on the block, but if you can’t use them it’s a waste. (Tip: What you’re recording on matters less than where you’re recording. Find a quiet place like a closet full of clothes to record in.)

You need to appreciate that there is a lot to learn and do before your first paid voice acting job. Yes, you want to get out there and start auditioning. But first, you’re going to need proper training, equipment, resources, and yes, some natural talent. The great news is that even though the voice over industry is competitive, there is plenty of voice over work out there for everyone. This guide on how to become a voice actor will give you a good idea of where to start.
Always update yourself on industry standard rates. I recommend reviewing the union rates set forth by SAG-AFTRA.  Voices.com also offers a rate card as well Voice-Over Resource Guide. Upon viewing these rates you may find, based on your current experience, you fall a little lower or higher than said rates. Maybe you have a great deal of experience in the commercial voice-over world, but now you’re branching out into narration, e-learning or audiobooks, so your voice-over rates may be a bit lower for that genre as you find your footing. The most important thing is that you have a baseline rate for yourself and you’re comfortable and confident stating this rate to a client. It’s beneficial to first ask your client’s budget and proceed from there. While stating your rate, also take into consideration edits and pick-ups. It’s customary to include one free round of edits in your rate, but any edits or pick-ups past that incur a fee.
I use the Adobe Audition package to edit my own voiceover work, but the techniques described below can be used in most audio‑editing software. Start by saving a new version of your original recording. (I keep the name of the file the same, but change the extension from _original to _edit.) Next, I'll turn my attention to the end of the recording, where I stepped away from the mic after the second take and recorded about 10 seconds of silence. Although processing is usually kept to a minimum, dealing with sibilance is important, and Eiosis' De‑esser plug‑in is much more precise than most.Wearing headphones, I can zoom in on this 'silence', turn up the volume, and listen for any background noise. If I notice any constant noise seeping into the recording, I may consider using Adobe Audition's noise‑reduction tool to capture a one‑ or two‑second profile of the silence, and then reduce the offending noise by about 75 percent throughout the recording. I should stress that this is rarely needed, and it's always a last resort, because such processing can generate swirly, metallic artifacts that draw more attention to themselves than the noise you intended to eliminate! But it's good to listen for such issues with fresh ears at the start of your editing session. If you find yourself using noise‑reduction often, that's a sign that you should find a better place to record, or improve the isolation of the space you've chosen. Don't forget that there are other ways to deal with some noise: often, a high‑pass filter is all you will need to clean up a recording, for example. Also remember that if your recording is to be mixed with music, slight background noise won't be noticeable, and that the more exposed your voice in the end product, the more problematic noise will become.
Even if you're mixing yourself, it's better to add EQ and compression only when you can hear how it will sit with the soundtrack or special effects. Ultimately, it comes down to knowing what your voice will be used for and making a judgement. For instance, if I'm recording a tagline for a TV or radio advert, I'll generally run a mic into a nice preamp (where I might add slight tube warmth, and subtle EQ or compression, just to give the recording a bit of 'body'), and I may do a little de‑essing using a plug‑in when performing any edits. However, for e‑learning jobs, corporate videos and so on, I'll tend not to add any creative processing while recording or editing, and will only use the de‑esser ever so slightly.
"The editing process for all our titles starts with receiving the Pro Tools sessions or WAV files and the engineer's script, which has the markings of how many takes there were, and which ones the director liked best. In some cases, I use Strip Silence and add a bed of room tone to expedite the assembly edit. In others I'll add the room tone as I move through the audio. Once I had all the final takes to be used in [Favorite African Folk Tales], I went back to do a fine‑edit pass and created notes on any issues, such as misreads, mispronunciations, noises, and so on. With that list, I was able to discuss with Alfre how we would address the issues. Since the actors' schedules did not permit them to come back in to do pick‑ups I had to do some creative editing.”

A great performance recorded on mediocre gear will always sound better than a mediocre performance recorded on great gear. By preparing well, before the session, you'll find it far easier to relax and focus on the message and the listener. As a producer, it's important to be clear what the expected format is for the final audio file. Although there are certain 'standards', your clients' expectations will vary.Read through the script, look up any questionable words and check their pronunciation. For American English, which accounts for the majority of my work, my favourite pronunciation resource is the Merriam‑Webster on‑line dictionary (www.m‑w.com), which includes audio examples. If you don't know how to pronounce the name of a company or product, call the company's customer service centre (if anyone can pronounce it right, they can!). If you don't know how to pronounce the name of a person or city, try searching YouTube for news reports on the subject.

No place is totally silent, so find the best place you can — even if that means thinking outside the box. I have a friend who regularly records his podcast in his car. He lives in a small house with dogs and kids, so there really isn’t anywhere else quiet enough. He takes his laptop and mic out to his driveway, shuts himself in the car and records. The results are surprisingly good!


“Bunny Studio Voice is an indispensable part of my production workflow. Using them saves me time and money compared to hiring a recording studio and VO artist. Without a doubt, their best feature is customer service. Thanks to their enormous support, I have saved DAYS off my deadlines and received pitch-perfect reads. I couldn’t recommend them more”
Fortunately, the internet has made this easier and more open. Most businesses have a logo, brand and a website. This forms the basis of how people get to know them. As a voice-over business you need to recognise that you need to market yourself. This involves ensuring you get your brand, your business, in front of the right people. Marketing though is also about building relationships with customers, not just selling to them. The more customers that use you on a regular basis the more money you can earn and the easier it becomes to achieve a good income.
First, I like to listen to the entire voice over recording from start to finish. I may make notes here and there to remind myself of something I want to go back and edit, but this time through I really just want to concentrate on the overall pacing and tone of the recording. Does it sound like I hoped? Did I rush or speak too slowly? Did I flub any words, mumble, or misspeak? Are there weird silences or unknown sounds?
Perhaps you come from a corporate business background, but you have a remarkable capacity for accents and original character voices, or you’ve been in radio and broadcasting for a number of years. If you’re an actor looking to expand your employment opportunities, mastering voiceover is imperative considering it’s required in every manner of recorded media: film, TV, animation, games, corporate industrials, and commercials. Whatever your specific experience has been to date, getting started in voiceover most often requires the following:
Before you get down to the nitty-gritty, though, I recommend doing a test recording to ensure your equipment works properly and your audio levels are strong. You don’t need to record the entire script, but a few paragraphs will give you enough to ensure that the audio is clear, at an appropriate level, and doesn’t include any stray or ambient noises.
"When recording voiceovers at home, you have to focus on performance: keep your energy levels up, stay true to the page, pronounce words correctly and consistently, and make sure you keep to a schedule to make the deadline. Prep well so you don't waste time second‑guessing yourself, looking up words as you go, and remember to not over‑ or under‑direct yourself. Also, make sure you know your recording equipment and room well; being able to quickly make adjustments to mic placement, levels, and so on, will make you more efficient.”
×