Next, run these files through any standard EQ high‑pass and low‑pass filters you use, zoom in on the waveform, and select a one‑second strip of silence from each recording. Save these strips as separate files. For instance, on my system, a one‑second strip of silence recorded at 16‑bit, 44.1kHz on a Neumann TLM103 would have this name: room_tone_neumann_tlm_103_44100_16_one_second.wav. Ideally, the noise floor of each strip will be lower than ‑60dB. Now, when you have to remove a bump or a squeak between words, you can paste in a piece of these strips instead of muting, which would draw attention to the edit.

It's only after this sort of processing that I'll start cleaning up the recording and dealing with the gaps of silence between spoken passages. A noise gate (or an off‑line 'strip‑silence' function) can be used to automatically mute sections that fall below a certain level. However, if not used carefully, these tools will clip the 'T's and 'P's off the ends of words, and shut out natural breathing sounds. Worse, if your recording is noisy, a noise gate will actually draw attention to the problem, since your client will be able to hear the difference between room tone and absolute muting. Another trick is to use a downward expander to reduce the noise floor of quiet sections, rather than cut out the noise completely.
Some of you might be wondering about the difference between voice over and narration. The short answer: not much. In most cases, you may use voice over and narration fairly interchangeably. However, to be technically correct, narration typically refers to an audio vocal that describes all the action on screen or tells a story based on what’s happening, while voice over may or may not describe as much action and is often more instructional in nature.
The advice we present here is tried, tested, and true. Peter Dickson is the foremost leading professional voice actor in the UK known for voicing the X-Factor, Britain’s Got Talent, Live at the Apollo, The London 2012 Olympic Games and countless brand commercials. In a stellar  career spanning 40 years, he has worked on over 120 TV shows and series, many of them award winning, been a promo voice on 60 TV and Radio channels around the world, been a featured voice actor on 30 AAA game titles, and voiced in excess of 30,000 radio and TV commercials!
The quality of your voice over depends almost entirely o the skill of the voice actor you use. A good voice actor will have perfect enunciation (ie, be very easy to understand), speak at an ideal pace (not too fast and not too slow), and have a pleasing voice. They should also be good at acting, and able to convey the feeling or emotions required by the script, using vocal variance and tone to keep the words interesting while also embodying the desired mood.
Another factor to consider is how the project is being used and in which medium. If you record a commercial that’s airing nationally on television, then that is a larger rate than a regional television commercial specific to a certain market. The voice-over spot you worked on is being seen by more viewers nationally as opposed to regionally, which warrants more compensation. You should not only consider your session fee, but also get the specifics on how the voice-over is being used. My personal opinion is to avoid “in perpetuity” usage because as your career develops, something which was not a conflict in the past could be in the future. If the spot you had conflicts with another brand in which you are auditioning, this could become a conflict that was unforeseen when you initially booked and recorded the job.

Perhaps you come from a corporate business background, but you have a remarkable capacity for accents and original character voices, or you’ve been in radio and broadcasting for a number of years. If you’re an actor looking to expand your employment opportunities, mastering voiceover is imperative considering it’s required in every manner of recorded media: film, TV, animation, games, corporate industrials, and commercials. Whatever your specific experience has been to date, getting started in voiceover most often requires the following:
Not all noise can be tackled in this way, though: you need to listen for clicks, plosives, digital glitches and the like. These can normally be acceptably repaired by using a 'heal' tool, or a pencil tool to redraw the waveform. Popped 'p's can often be 'fixed' using a high‑pass filter set at 100Hz. For a single glitch, you can zoom in and cut out the cycle of the waveform in which the glitch appears. Just be careful to start and end the cut where the waveform crosses the centre line, otherwise you'll inadvertently add another digital glitch. If glitches are frequent, it's likely that there's a problem with your audio interface's buffer settings — it may be just a playback issue.
The annual income of a voice talent varies greatly from person to person and from year to year. When you’re just starting out most of what you earn from voice over work should be reinvested into your studio, demos, and marketing efforts, so at this stage you will need a second job to support your daily living expenses. Once you start building a portfolio of clients, you’ll see your regular earnings grow and will really start to get a feel for the potential your voice over business has. In time, you’ll be enjoying a satisfying career.
One of the big changes to the world of voice acting is that today most voice actors work from home, in their own recording studios. This appeals to many people who want to develop a lifestyle that allows them to work from home. This guide on how to become a voice actor, explains how you can develop your voice and learn what steps you need to take to start learning the art of voice acting.
Always keep it professional. A client may not have a budget that works within your rates presently, but one day they may have a project with a much larger budget and think of you as the talent to circle back to! It never hurts to politely decline when a project has too low of a rate and exclaim, “I would love to work with you in the future when our rates align!”
Also listen for sibilance. Strong 'ess' sounds are best corrected at source, by using good mic technique, but sometimes they're unavoidable. If you hear an 'ess' that really sizzles in your recording, you can manually reduce its volume. You can, of course, also use a de‑esser, but do be careful, as applying some de‑essers to the entire audio file can alter the sound of your recording. It often works best to apply them to short sections, either offline or using automation. My preferred de‑esser plug‑in is the one sold by Eiosis (www.eiosis.com),Make sure you record some silence at the end of each take. That way, if a great performance suffers from noise issues, you have something to feed your noise‑reduction processors. Just don't rely on this technique too much! which cleverly separates the esses from the rest of the audio and allows you to manipulate them independently. If you want to learn about some more advanced strategies for de‑essing check out Mike Senior's article from SOS May 2009 (/sos/may09/articles/deessing.htm).
"You need to be able to pull the listener in, help them suspend disbelief, become a part of the world the author created, and take the journey with your voice as the guide. Practice your character voices; they must be believable and honest. Work on your accents and timing and delivery within different genres. When reading, read out loud — even if you're not recording or being paid for it. This will help you with flow and dialogue. Listen to other audiobooks and figure out what you like and don't like, then work on these factors in your own performances. Working from a home studio, you have many more responsibilities to consider. Be mindful of them, set attainable goals and know your limitations. Never over-promise and under-deliver to a client. There are many established and aspiring narrators out there, so bring your best to the table.”
Next, run these files through any standard EQ high‑pass and low‑pass filters you use, zoom in on the waveform, and select a one‑second strip of silence from each recording. Save these strips as separate files. For instance, on my system, a one‑second strip of silence recorded at 16‑bit, 44.1kHz on a Neumann TLM103 would have this name: room_tone_neumann_tlm_103_44100_16_one_second.wav. Ideally, the noise floor of each strip will be lower than ‑60dB. Now, when you have to remove a bump or a squeak between words, you can paste in a piece of these strips instead of muting, which would draw attention to the edit.
ADR / Automated Dialogue Replacement in Salt Lake City, Utah Audio Mixing / Sound Recording Equipment Rentals in Salt Lake City, Utah Audio Mixing / Sweetening / Sound Editing / Sound Designers in Salt Lake City, Utah Audio Technicians / Audio Engineer / A1 / A2 in Salt Lake City, Utah Film Post Production Services in Salt Lake City, Utah Foley Stages in Salt Lake City, Utah Post House / Video Post Production Facilities / Editing Services in Salt Lake City, Utah Recording Studios in Salt Lake City, Utah Sound Mixers / Recordists in Salt Lake City, Utah Voice Over Artists in Salt Lake City, Utah
"Ideally the talent should be seated, staying on axis, approximately a foot away from the mic, which should be angled back from the face a bit, not parallel to it. You'll need to see what angle provides the best results, usually a few degrees off from parallel works great — and located between the forehead and the nose, not directly in line with the mouth. This will help with plosives, mouth noise, and some other issues. Movement in the booth should be limited, as the microphone is likely to pick up arms flailing, hands rubbing, page turns, stomach growling, and so on. Keep the levels consistent, moving closer if the scene calls for a whisper, or moving back for a loud voice or scream. A well‑versed narrator is capable of delivering a dynamic performance without creating dynamic levels.”
The advice we present here is tried, tested, and true. Peter Dickson is the foremost leading professional voice actor in the UK known for voicing the X-Factor, Britain’s Got Talent, Live at the Apollo, The London 2012 Olympic Games and countless brand commercials. In a stellar  career spanning 40 years, he has worked on over 120 TV shows and series, many of them award winning, been a promo voice on 60 TV and Radio channels around the world, been a featured voice actor on 30 AAA game titles, and voiced in excess of 30,000 radio and TV commercials!
Even if you're mixing yourself, it's better to add EQ and compression only when you can hear how it will sit with the soundtrack or special effects. Ultimately, it comes down to knowing what your voice will be used for and making a judgement. For instance, if I'm recording a tagline for a TV or radio advert, I'll generally run a mic into a nice preamp (where I might add slight tube warmth, and subtle EQ or compression, just to give the recording a bit of 'body'), and I may do a little de‑essing using a plug‑in when performing any edits. However, for e‑learning jobs, corporate videos and so on, I'll tend not to add any creative processing while recording or editing, and will only use the de‑esser ever so slightly.
Voice over is a production technique where a voice that is not part of the narrative is heard over the action. It’s often used in movies, TV shows, plays, or other presentations. Voice over is an effective way to convey information that doesn’t naturally fit into the plot or the other visual elements that are occurring. Voice over work is read by a voice actor who reads from a script, and it is added to the other elements during production.
"You need to be able to pull the listener in, help them suspend disbelief, become a part of the world the author created, and take the journey with your voice as the guide. Practice your character voices; they must be believable and honest. Work on your accents and timing and delivery within different genres. When reading, read out loud — even if you're not recording or being paid for it. This will help you with flow and dialogue. Listen to other audiobooks and figure out what you like and don't like, then work on these factors in your own performances. Working from a home studio, you have many more responsibilities to consider. Be mindful of them, set attainable goals and know your limitations. Never over-promise and under-deliver to a client. There are many established and aspiring narrators out there, so bring your best to the table.”
"You need to be able to pull the listener in, help them suspend disbelief, become a part of the world the author created, and take the journey with your voice as the guide. Practice your character voices; they must be believable and honest. Work on your accents and timing and delivery within different genres. When reading, read out loud — even if you're not recording or being paid for it. This will help you with flow and dialogue. Listen to other audiobooks and figure out what you like and don't like, then work on these factors in your own performances. Working from a home studio, you have many more responsibilities to consider. Be mindful of them, set attainable goals and know your limitations. Never over-promise and under-deliver to a client. There are many established and aspiring narrators out there, so bring your best to the table.”
I use the Adobe Audition package to edit my own voiceover work, but the techniques described below can be used in most audio‑editing software. Start by saving a new version of your original recording. (I keep the name of the file the same, but change the extension from _original to _edit.) Next, I'll turn my attention to the end of the recording, where I stepped away from the mic after the second take and recorded about 10 seconds of silence. Although processing is usually kept to a minimum, dealing with sibilance is important, and Eiosis' De‑esser plug‑in is much more precise than most.Wearing headphones, I can zoom in on this 'silence', turn up the volume, and listen for any background noise. If I notice any constant noise seeping into the recording, I may consider using Adobe Audition's noise‑reduction tool to capture a one‑ or two‑second profile of the silence, and then reduce the offending noise by about 75 percent throughout the recording. I should stress that this is rarely needed, and it's always a last resort, because such processing can generate swirly, metallic artifacts that draw more attention to themselves than the noise you intended to eliminate! But it's good to listen for such issues with fresh ears at the start of your editing session. If you find yourself using noise‑reduction often, that's a sign that you should find a better place to record, or improve the isolation of the space you've chosen. Don't forget that there are other ways to deal with some noise: often, a high‑pass filter is all you will need to clean up a recording, for example. Also remember that if your recording is to be mixed with music, slight background noise won't be noticeable, and that the more exposed your voice in the end product, the more problematic noise will become.
The point is each person can often have a different perspective on how they ‘bid’ for work. Another factor is how you work within an industry if you have a really high profile. For instance if a big car manufacturer chooses you, you’re not going to get any kind of work from any other car manufacturer so you’re alienating yourself out of the rest of the market for the big players.

There are two main priorities in voiceover work: the message that you're being asked to convey; and invisibility — by which I mean you never want people to notice your voice. This might sound counter‑intuitive. After all, why not make your voice sound great? Well, you need the listener to focus on the message your client is paying you to get across, rather than your voice itself, so it needs to sound natural. Even for tag lines, where you might think a fuller, warmer, more compressed (or whatever) voice would be appropriate, the production house will often want to perform EQ and compression themselves. This lesson took me a long time to learn, but my clients are much happier when I send them a nice, dry recording. I simply remind myself that I'm supplying the raw material for them to add to their mix, and letting them make their magic.

At this point — unless you're tracking for broadcast applications (where they don't work to peak levels) — consider 'normalising' your recording to an optimal level. Normalisation can be used to push the loudest peak to around ‑1dB and increase the volume of the entire recording by the same ratio. Of course, you can also tighten up dynamic range (the difference between the softest and loudest parts of your recording) by manually reducing the loudest sections of the recording before you apply normalisation. On a final note, if you do plan to use a compressor, then you might as well add gain at that stage instead of normalising.

×