As the engineer, your key job is to select and set up the recording space, choose and position the microphone, set levels and make sure you're recording a good, clean signal at a healthy level. Like music, the louder the signal you want to record, the less audible the noise floor, but you don't want to have to speak louder than sounds natural, and you don't want to overcook things when tracking: any distortion will be very noticeable on an exposed voice part, and an otherwise great take with digital clipping won't be acceptable. If you notice clipping only when you start editing, software clip restoration tools might help to make the take usable, but it's not going to be perfect. Remember that although you may have needed to record 'hot' on analogue tape and older 16‑bit digital recording systems, modern 24‑bit A‑D converters can accommodate a much wider dynamic range, so you no longer have to track so loud: you can leave much more headroom.

This guide is designed to give you an insight into this hidden world and provide you with enough information to help you make an informed choice on whether or not this is a potential career for you. If you already are a voice actor, we will be giving you some tips and ideas to help you improve your voice acting skills to help you experience a dramatic difference in how you approach the written word.


It's only after this sort of processing that I'll start cleaning up the recording and dealing with the gaps of silence between spoken passages. A noise gate (or an off‑line 'strip‑silence' function) can be used to automatically mute sections that fall below a certain level. However, if not used carefully, these tools will clip the 'T's and 'P's off the ends of words, and shut out natural breathing sounds. Worse, if your recording is noisy, a noise gate will actually draw attention to the problem, since your client will be able to hear the difference between room tone and absolute muting. Another trick is to use a downward expander to reduce the noise floor of quiet sections, rather than cut out the noise completely.
Next, run these files through any standard EQ high‑pass and low‑pass filters you use, zoom in on the waveform, and select a one‑second strip of silence from each recording. Save these strips as separate files. For instance, on my system, a one‑second strip of silence recorded at 16‑bit, 44.1kHz on a Neumann TLM103 would have this name: room_tone_neumann_tlm_103_44100_16_one_second.wav. Ideally, the noise floor of each strip will be lower than ‑60dB. Now, when you have to remove a bump or a squeak between words, you can paste in a piece of these strips instead of muting, which would draw attention to the edit.
Next, run these files through any standard EQ high‑pass and low‑pass filters you use, zoom in on the waveform, and select a one‑second strip of silence from each recording. Save these strips as separate files. For instance, on my system, a one‑second strip of silence recorded at 16‑bit, 44.1kHz on a Neumann TLM103 would have this name: room_tone_neumann_tlm_103_44100_16_one_second.wav. Ideally, the noise floor of each strip will be lower than ‑60dB. Now, when you have to remove a bump or a squeak between words, you can paste in a piece of these strips instead of muting, which would draw attention to the edit.
Union and non-union jobs have always been two separate markets. Non-union work is more visible and attractive today when compared to years ago, due to online casting. The availability of professional talent for non-union work has led to a reshaping of the voice over industry. An open market means that each professional voice actor sets their own rate based on what they need to cover.
A demo recording of you doing voice-over work is your CV and your business card combined. If you're applying for a voice-over job, you can send the potential customer your demo via the Internet. Ideally you have multiple demos for different types of gigs. For commercials, clients want to hear 60 to 90 seconds of voice work. If you're auditioning as an audiobook reader, five minutes of demo proves that you can stay in character over a longer stretch of time.

Before you do anything though, ask yourself why you want to become a voice actor. If you know upfront what your goals, expectations, and motivations are, you will be more successful. Setting small achievable goals and placing deadlines on them will make sure you stay on track, even if you only want to do voice over as a hobby instead of a full-time career.
One of my favorite things about being a voice-over actor is the incredibly supportive community. Use your community to communicate with other voice-over actors regarding rates and best business practices. I have rarely found anyone who is secretive or not willing to share their past experiences. By being a generous and communicative community, we are stronger as voice actors and can advocate for ourselves to get paid appropriately. If you are operating from a home studio and all communication is between yourself and the client (versus an agent as the intermediary) it’s usually your responsibility to invoice after sending your VO files. I always include a polite 30-day payment term at the bottom of my invoice. In certain states (for example, New York) there is a “Freelancing isn’t Free Act”, in which you can politely mention to be paid in a timely manner.
When you come to actually recording your voice, try to think of the mic as the ear of your listener. Picture your listener, have an opinion, and read the script as if the words were coming to mind that instant. The distance between your mouth and the mic should be about the same as the distance between your thumb and pinkie when making a hang‑five gesture (see the picture above). Move closer to the mic when you lower your voice and back off when you speak louder. On‑line dictionaries such as the Merriam‑Webster one pictured here, often include audio examples which can help you clarify pronunciation. Just make sure that you use an American English or UK English (or other language!) version as appropriate. (Remember, while you have your engineer hat on, to take account of this when setting levels.) Always use a pop shield, and I'd suggest trying to work slightly off‑axis, as talking to a point just to the right or left of the mic will prevent bursts of air and drops of saliva ruining your recording. I'd also recommend wearing headphones over one ear only, as this allows you to judge volume and listen for clipping and plosives on the recording, while also hearing your natural voice, which makes it easier to focus on that message we talked about. Simone demonstrates this technique in the picture on the next page. Hhe's working slightly off‑axis and has backed off an inch or two to deliver with more energy.Typically, you'd record with your mouth approximately the distance between your thumb and little finger from the mic, as pictured here.
It's only after this sort of processing that I'll start cleaning up the recording and dealing with the gaps of silence between spoken passages. A noise gate (or an off‑line 'strip‑silence' function) can be used to automatically mute sections that fall below a certain level. However, if not used carefully, these tools will clip the 'T's and 'P's off the ends of words, and shut out natural breathing sounds. Worse, if your recording is noisy, a noise gate will actually draw attention to the problem, since your client will be able to hear the difference between room tone and absolute muting. Another trick is to use a downward expander to reduce the noise floor of quiet sections, rather than cut out the noise completely.
Always update yourself on industry standard rates. I recommend reviewing the union rates set forth by SAG-AFTRA.  Voices.com also offers a rate card as well Voice-Over Resource Guide. Upon viewing these rates you may find, based on your current experience, you fall a little lower or higher than said rates. Maybe you have a great deal of experience in the commercial voice-over world, but now you’re branching out into narration, e-learning or audiobooks, so your voice-over rates may be a bit lower for that genre as you find your footing. The most important thing is that you have a baseline rate for yourself and you’re comfortable and confident stating this rate to a client. It’s beneficial to first ask your client’s budget and proceed from there. While stating your rate, also take into consideration edits and pick-ups. It’s customary to include one free round of edits in your rate, but any edits or pick-ups past that incur a fee.
When you come to actually recording your voice, try to think of the mic as the ear of your listener. Picture your listener, have an opinion, and read the script as if the words were coming to mind that instant. The distance between your mouth and the mic should be about the same as the distance between your thumb and pinkie when making a hang‑five gesture (see the picture above). Move closer to the mic when you lower your voice and back off when you speak louder. On‑line dictionaries such as the Merriam‑Webster one pictured here, often include audio examples which can help you clarify pronunciation. Just make sure that you use an American English or UK English (or other language!) version as appropriate. (Remember, while you have your engineer hat on, to take account of this when setting levels.) Always use a pop shield, and I'd suggest trying to work slightly off‑axis, as talking to a point just to the right or left of the mic will prevent bursts of air and drops of saliva ruining your recording. I'd also recommend wearing headphones over one ear only, as this allows you to judge volume and listen for clipping and plosives on the recording, while also hearing your natural voice, which makes it easier to focus on that message we talked about. Simone demonstrates this technique in the picture on the next page. Hhe's working slightly off‑axis and has backed off an inch or two to deliver with more energy.Typically, you'd record with your mouth approximately the distance between your thumb and little finger from the mic, as pictured here.
×