As the engineer, your key job is to select and set up the recording space, choose and position the microphone, set levels and make sure you're recording a good, clean signal at a healthy level. Like music, the louder the signal you want to record, the less audible the noise floor, but you don't want to have to speak louder than sounds natural, and you don't want to overcook things when tracking: any distortion will be very noticeable on an exposed voice part, and an otherwise great take with digital clipping won't be acceptable. If you notice clipping only when you start editing, software clip restoration tools might help to make the take usable, but it's not going to be perfect. Remember that although you may have needed to record 'hot' on analogue tape and older 16‑bit digital recording systems, modern 24‑bit A‑D converters can accommodate a much wider dynamic range, so you no longer have to track so loud: you can leave much more headroom.
The contents of this article are subject to worldwide copyright protection and reproduction in whole or part, whether mechanical or electronic, is expressly forbidden without the prior written consent of the Publishers. Great care has been taken to ensure accuracy in the preparation of this article but neither Sound On Sound Limited nor the publishers can be held responsible for its contents. The views expressed are those of the contributors and not necessarily those of the publishers.
Hey Rob. You certainly know your stuff. I know this for a fact, because I’ve been a working professional at this for nearly ten years and spend every week since that time making mistakes and learning from them. I also incorporate 99 percent of your suggestions here and believe it folks they work, if used properly. Very informative and practical. Thanks, Rob.
As I've mentioned, most of our clients prefer to do post‑production work themselves, and request the raw (but edited) recordings. Sometimes, though, as in the Avast! job, the client will want the files ready to go, which might mean using slight EQ and compression. The noise floor on my recordings generally hovers around ‑54dB, but by using EQ to roll off frequencies below 80Hz and above 12kHz, I am usually able to lower the noise floor to around ‑57dB without resorting to noise reduction. Using EQ to reduce low‑end rumble and high‑frequency noise will make your recording sound better, and will be particularly beneficial if you'll be adding compression later, as the compressor's make-up gain won't be raising the level of that noise. Used moderately, compression can usefully reduce dynamic range, and thus improve intelligibility of the words, while still leaving you with a natural‑sounding result. Used excessively, it will suck the life out of a recording.
It's only after this sort of processing that I'll start cleaning up the recording and dealing with the gaps of silence between spoken passages. A noise gate (or an off‑line 'strip‑silence' function) can be used to automatically mute sections that fall below a certain level. However, if not used carefully, these tools will clip the 'T's and 'P's off the ends of words, and shut out natural breathing sounds. Worse, if your recording is noisy, a noise gate will actually draw attention to the problem, since your client will be able to hear the difference between room tone and absolute muting. Another trick is to use a downward expander to reduce the noise floor of quiet sections, rather than cut out the noise completely.
Hiring a voice actor can be intimidating, especially if you have not done it before. After all, the voice that reads your script is the most powerful connector you have with your audience — the voice quality brings emotion and a sensory experience to your video. Here are a few guidelines to managing your search and relationship with voice over talent.
Some of you might be wondering about the difference between voice over and narration. The short answer: not much. In most cases, you may use voice over and narration fairly interchangeably. However, to be technically correct, narration typically refers to an audio vocal that describes all the action on screen or tells a story based on what’s happening, while voice over may or may not describe as much action and is often more instructional in nature.
Perhaps you come from a corporate business background, but you have a remarkable capacity for accents and original character voices, or you’ve been in radio and broadcasting for a number of years. If you’re an actor looking to expand your employment opportunities, mastering voiceover is imperative considering it’s required in every manner of recorded media: film, TV, animation, games, corporate industrials, and commercials. Whatever your specific experience has been to date, getting started in voiceover most often requires the following: 

You need to appreciate that there is a lot to learn and do before your first paid voice acting job. Yes, you want to get out there and start auditioning. But first, you’re going to need proper training, equipment, resources, and yes, some natural talent. The great news is that even though the voice over industry is competitive, there is plenty of voice over work out there for everyone. This guide on how to become a voice actor will give you a good idea of where to start.
The quality of your voice over depends almost entirely o the skill of the voice actor you use. A good voice actor will have perfect enunciation (ie, be very easy to understand), speak at an ideal pace (not too fast and not too slow), and have a pleasing voice. They should also be good at acting, and able to convey the feeling or emotions required by the script, using vocal variance and tone to keep the words interesting while also embodying the desired mood.
The advice we present here is tried, tested, and true. Peter Dickson is the foremost leading professional voice actor in the UK known for voicing the X-Factor, Britain’s Got Talent, Live at the Apollo, The London 2012 Olympic Games and countless brand commercials. In a stellar  career spanning 40 years, he has worked on over 120 TV shows and series, many of them award winning, been a promo voice on 60 TV and Radio channels around the world, been a featured voice actor on 30 AAA game titles, and voiced in excess of 30,000 radio and TV commercials!

If a client likes your demo, they may invite you to audition. In the 21st century, you can download the audition script, record the audition at home, and then send the results to your client over the Internet. Prepare yourself for a life of constant auditions: Even successful voice pros may do many more auditions than actual jobs. But if enough jobs come your way, it's worth it.
Why the difference in approach? Lots of my e‑learning and corporate jobs are done for production houses that will be adding other voices to the mix. Ironically, if I record my voice via a great mic and preamp, and add some nice processing, it can end up standing out from the other voices, drawing attention to itself. The production house will see this as me causing them a problem, even though my recording sounds better than the others!
Working with a top voiceover agency can bring you a steady stream of well paid work. The top voiceover agencies, like Hobsons in London or Abrams in NY and LA, have an elite set of voice actors as well as recognised visual actors who do voiceover. These top agencies are hard to get into though. They only take the very best established voice talent.
While having a broad set of voice skills is beneficial, many voice overs establish themselves in commercials and more general corporate voiceover work before specialising. Having a niche or specialist focus though can make a difference in earning potential. So, bearing in mind the question: how much money do a voice actors make, will also depend on the level and experience in a given niche e.g. animation, audiobooks or gaming.
In late 2009, my wife Simone received an email from Prague in the Czech Republic. The sender, Mirek Jirku, was heading up a project to record voice messages for the foreign‑language versions of the latest Avast! anti‑virus software. Mirek sent us eight messages to be recorded, specified the fee and deadline, and requested a slow, friendly read. He asked us to send separate stereo MP3 files (at 160kbps or higher quality) for each message, specified that we'd have to sign a non‑disclosure agreement before recording, that we'd need to invoice afterwards, and that he'd pay via a wire transfer instead of PayPal (which is often used for international payments).
When you come to actually recording your voice, try to think of the mic as the ear of your listener. Picture your listener, have an opinion, and read the script as if the words were coming to mind that instant. The distance between your mouth and the mic should be about the same as the distance between your thumb and pinkie when making a hang‑five gesture (see the picture above). Move closer to the mic when you lower your voice and back off when you speak louder. On‑line dictionaries such as the Merriam‑Webster one pictured here, often include audio examples which can help you clarify pronunciation. Just make sure that you use an American English or UK English (or other language!) version as appropriate. (Remember, while you have your engineer hat on, to take account of this when setting levels.) Always use a pop shield, and I'd suggest trying to work slightly off‑axis, as talking to a point just to the right or left of the mic will prevent bursts of air and drops of saliva ruining your recording. I'd also recommend wearing headphones over one ear only, as this allows you to judge volume and listen for clipping and plosives on the recording, while also hearing your natural voice, which makes it easier to focus on that message we talked about. Simone demonstrates this technique in the picture on the next page. Hhe's working slightly off‑axis and has backed off an inch or two to deliver with more energy.Typically, you'd record with your mouth approximately the distance between your thumb and little finger from the mic, as pictured here.
Always update yourself on industry standard rates. I recommend reviewing the union rates set forth by SAG-AFTRA.  Voices.com also offers a rate card as well Voice-Over Resource Guide. Upon viewing these rates you may find, based on your current experience, you fall a little lower or higher than said rates. Maybe you have a great deal of experience in the commercial voice-over world, but now you’re branching out into narration, e-learning or audiobooks, so your voice-over rates may be a bit lower for that genre as you find your footing. The most important thing is that you have a baseline rate for yourself and you’re comfortable and confident stating this rate to a client. It’s beneficial to first ask your client’s budget and proceed from there. While stating your rate, also take into consideration edits and pick-ups. It’s customary to include one free round of edits in your rate, but any edits or pick-ups past that incur a fee.
The point is each person can often have a different perspective on how they ‘bid’ for work. Another factor is how you work within an industry if you have a really high profile. For instance if a big car manufacturer chooses you, you’re not going to get any kind of work from any other car manufacturer so you’re alienating yourself out of the rest of the market for the big players.
First of all let’s dismiss the obvious – there is no such thing as a standard rate, there are only guide lines and even these vary by Country and type of work. The only standard rates are those set by some Union scale rates. One of the most notable differences is that between voice over union rates and voice over rates non-union. Unions provide a standard voiceover rate and therefore you can safely rely on the unions guide (depending on which Country you are in). However, non union voice over rates vary enormously and are often down to negotiations between the voice over actor and the client.
ADR / Automated Dialogue Replacement in Salt Lake City, Utah Audio Mixing / Sound Recording Equipment Rentals in Salt Lake City, Utah Audio Mixing / Sweetening / Sound Editing / Sound Designers in Salt Lake City, Utah Audio Technicians / Audio Engineer / A1 / A2 in Salt Lake City, Utah Film Post Production Services in Salt Lake City, Utah Foley Stages in Salt Lake City, Utah Post House / Video Post Production Facilities / Editing Services in Salt Lake City, Utah Recording Studios in Salt Lake City, Utah Sound Mixers / Recordists in Salt Lake City, Utah Voice Over Artists in Salt Lake City, Utah
Before you do anything though, ask yourself why you want to become a voice actor. If you know upfront what your goals, expectations, and motivations are, you will be more successful. Setting small achievable goals and placing deadlines on them will make sure you stay on track, even if you only want to do voice over as a hobby instead of a full-time career.
A demo recording of you doing voice-over work is your CV and your business card combined. If you're applying for a voice-over job, you can send the potential customer your demo via the Internet. Ideally you have multiple demos for different types of gigs. For commercials, clients want to hear 60 to 90 seconds of voice work. If you're auditioning as an audiobook reader, five minutes of demo proves that you can stay in character over a longer stretch of time.
×