Finally, as you complete more work, you can end up with a lot of different files from your projects, so good 'housekeeping' of your sessions and recordings is a must. Glancing at the filename simone_kliass_avast_virus_database_neumann_tlm_103_original.wav, I can easily tell that this is the original recording of my wife's "Your virus database has been updated” message in Portuguese for Avast! on a Neumann TLM103 mic. It doesn't matter what your system is, as long as it works and you can stick to it.
Not all noise can be tackled in this way, though: you need to listen for clicks, plosives, digital glitches and the like. These can normally be acceptably repaired by using a 'heal' tool, or a pencil tool to redraw the waveform. Popped 'p's can often be 'fixed' using a high‑pass filter set at 100Hz. For a single glitch, you can zoom in and cut out the cycle of the waveform in which the glitch appears. Just be careful to start and end the cut where the waveform crosses the centre line, otherwise you'll inadvertently add another digital glitch. If glitches are frequent, it's likely that there's a problem with your audio interface's buffer settings — it may be just a playback issue.
"You need to be able to pull the listener in, help them suspend disbelief, become a part of the world the author created, and take the journey with your voice as the guide. Practice your character voices; they must be believable and honest. Work on your accents and timing and delivery within different genres. When reading, read out loud — even if you're not recording or being paid for it. This will help you with flow and dialogue. Listen to other audiobooks and figure out what you like and don't like, then work on these factors in your own performances. Working from a home studio, you have many more responsibilities to consider. Be mindful of them, set attainable goals and know your limitations. Never over-promise and under-deliver to a client. There are many established and aspiring narrators out there, so bring your best to the table.”
“Bunny Studio Voice has a very efficient process to help us identify the right voice actors that best meet each of our video’s needs. Their platform keeps us informed throughout the process, from the actor accepting the project all the way through when the recording is complete. I highly recommend them as a reliable, high quality and cost-effective voice over provider”
Some clients are not experienced in voice over. So another way you can help them is to advice then and help them really understand all that goes into a voice over recording to get it to the final polished result. Of course you need to take this into account when you charge for your time and again whether this is a one off project or has potential to be a long term client.
"The editing process for all our titles starts with receiving the Pro Tools sessions or WAV files and the engineer's script, which has the markings of how many takes there were, and which ones the director liked best. In some cases, I use Strip Silence and add a bed of room tone to expedite the assembly edit. In others I'll add the room tone as I move through the audio. Once I had all the final takes to be used in [Favorite African Folk Tales], I went back to do a fine‑edit pass and created notes on any issues, such as misreads, mispronunciations, noises, and so on. With that list, I was able to discuss with Alfre how we would address the issues. Since the actors' schedules did not permit them to come back in to do pick‑ups I had to do some creative editing.”
You start off each job as a producer, consulting your client and getting briefed on the project at hand. Then you become an engineer, dealing with recording gear and software, setting the mic position and levels. Next, you step up to the mic as an actor, bringing the script off the page and connecting with the listener. Meanwhile, the director in you sits behind the metaphorical glass, making sure the actor doesn't mispronounce a word or stumble through a passage of text. Then you're an editor, cleaning up the best take and sending the resulting audio to your client. You need to be able to perform all of these roles to a high standard, and the better you are at each, the more your business will prosper.
As the engineer, your key job is to select and set up the recording space, choose and position the microphone, set levels and make sure you're recording a good, clean signal at a healthy level. Like music, the louder the signal you want to record, the less audible the noise floor, but you don't want to have to speak louder than sounds natural, and you don't want to overcook things when tracking: any distortion will be very noticeable on an exposed voice part, and an otherwise great take with digital clipping won't be acceptable. If you notice clipping only when you start editing, software clip restoration tools might help to make the take usable, but it's not going to be perfect. Remember that although you may have needed to record 'hot' on analogue tape and older 16‑bit digital recording systems, modern 24‑bit A‑D converters can accommodate a much wider dynamic range, so you no longer have to track so loud: you can leave much more headroom.

Your own voice is your most important piece of equipment. If you're new to the voice-acting world, look around to see if there are classes or coaching in your area. Outside of class, practice speaking clearly and confidently. Learn to do this even with material you've never seen before. It's also important to learn voice care – straining or injuring your voice can hurt you and your career.
© 2020 GoAnimate, Inc. All Rights Reserved. VYOND™ is a trademark of GoAnimate, Inc., registered in Australia, Brazil, Chile, the European Union, Hong Kong, India, Israel, Mexico, New Zealand, Norway, OAPI, the Philippines, Singapore, Switzerland, the United Kingdom, and Vietnam; Reg. U.S. Pat. & Tm. Off. Other names and marks are the property of their respective holders.
Because I've prepared properly, the first take is often the one I end up editing and sending to my client. The second is simply there as a safety net, in case I need to replace any mistakes while editing. It's much better to capture such drop‑ins during the same session as the main performance, as you can be sure that the mic will be in the same place and your voice will have a similar character in both takes.

There are now more opportunities in the voiceover industry than ever before — but competition has never been so fierce — so, in this short series of articles I'll set out what you need to know to get started as a home‑studio voiceover artist, and turn it into a paying job. This month, I'll explain some differences between the voiceover and music industries, and run through the different roles you'll need to become good at. Next time, I'll discuss what makes a good voice, the sort of home‑studio setup you need, and how you can start to get the jobs coming in.
Important: Use headphones to check the audio quality of your test recording. Your computer speakers will not be good enough for this. Headphones allow you to listen closely to ensure clear audio. Obviously, you want the audio to sound good on even the cheapest speaker, but you will be much happier if you use headphones. Remember, a good portion of your video viewers will listen this way, so you want to be sure they’ll have an optimal experience.
"This was Alfre Woodard's audiobook directing debut, and she pulled an amazing performance from people. The big [thing] was to remember that these stories were being told in intimate settings, one‑on‑one in most cases, so the talent really needed to speak to the individual listener. An image kept in mind was stories being told around a campfire, back when folktales were passed down by spoken word.”

Before you get down to the nitty-gritty, though, I recommend doing a test recording to ensure your equipment works properly and your audio levels are strong. You don’t need to record the entire script, but a few paragraphs will give you enough to ensure that the audio is clear, at an appropriate level, and doesn’t include any stray or ambient noises.
When you come to actually recording your voice, try to think of the mic as the ear of your listener. Picture your listener, have an opinion, and read the script as if the words were coming to mind that instant. The distance between your mouth and the mic should be about the same as the distance between your thumb and pinkie when making a hang‑five gesture (see the picture above). Move closer to the mic when you lower your voice and back off when you speak louder. On‑line dictionaries such as the Merriam‑Webster one pictured here, often include audio examples which can help you clarify pronunciation. Just make sure that you use an American English or UK English (or other language!) version as appropriate. (Remember, while you have your engineer hat on, to take account of this when setting levels.) Always use a pop shield, and I'd suggest trying to work slightly off‑axis, as talking to a point just to the right or left of the mic will prevent bursts of air and drops of saliva ruining your recording. I'd also recommend wearing headphones over one ear only, as this allows you to judge volume and listen for clipping and plosives on the recording, while also hearing your natural voice, which makes it easier to focus on that message we talked about. Simone demonstrates this technique in the picture on the next page. Hhe's working slightly off‑axis and has backed off an inch or two to deliver with more energy.Typically, you'd record with your mouth approximately the distance between your thumb and little finger from the mic, as pictured here.
×