"Ideally the talent should be seated, staying on axis, approximately a foot away from the mic, which should be angled back from the face a bit, not parallel to it. You'll need to see what angle provides the best results, usually a few degrees off from parallel works great — and located between the forehead and the nose, not directly in line with the mouth. This will help with plosives, mouth noise, and some other issues. Movement in the booth should be limited, as the microphone is likely to pick up arms flailing, hands rubbing, page turns, stomach growling, and so on. Keep the levels consistent, moving closer if the scene calls for a whisper, or moving back for a loud voice or scream. A well‑versed narrator is capable of delivering a dynamic performance without creating dynamic levels.”

The contents of this article are subject to worldwide copyright protection and reproduction in whole or part, whether mechanical or electronic, is expressly forbidden without the prior written consent of the Publishers. Great care has been taken to ensure accuracy in the preparation of this article but neither Sound On Sound Limited nor the publishers can be held responsible for its contents. The views expressed are those of the contributors and not necessarily those of the publishers.
A better, more natural-sounding way to clean up a voice recording, though, is to paste in strips of 'silence' that showcase your home studio at its best. To do this, wake up early (ie. when your house is quiet), turn on your gear and set your levels for a normal job. Then record a full minute of silence at whatever bit depths and sample rates you're likely to be using. Repeat this process for each different mic you use, and save each file in a folder titled Room Tones, or something similarly suitable.
Hey Rob. You certainly know your stuff. I know this for a fact, because I’ve been a working professional at this for nearly ten years and spend every week since that time making mistakes and learning from them. I also incorporate 99 percent of your suggestions here and believe it folks they work, if used properly. Very informative and practical. Thanks, Rob.
Recording voice overs like a pro isn’t that difficult when you know how to do it. You may have noticed that the actual recording part plays little part when compared to the preparation. Taking the proper steps before you hit the record button and then taking the time to edit your audio appropriately will go a long way to ensuring your voice overs sound professional and engaging.
Like any relationship, communication is key when bringing voice talent on to your project. This video is your baby, something you’ve been working on for awhile, so you will get the best results if you can communicate your vision for the project. Provide background on your brand, on your customers, because your voice actor can use these details like fuel to accurately represent your brand.
I use the Adobe Audition package to edit my own voiceover work, but the techniques described below can be used in most audio‑editing software. Start by saving a new version of your original recording. (I keep the name of the file the same, but change the extension from _original to _edit.) Next, I'll turn my attention to the end of the recording, where I stepped away from the mic after the second take and recorded about 10 seconds of silence. Although processing is usually kept to a minimum, dealing with sibilance is important, and Eiosis' De‑esser plug‑in is much more precise than most.Wearing headphones, I can zoom in on this 'silence', turn up the volume, and listen for any background noise. If I notice any constant noise seeping into the recording, I may consider using Adobe Audition's noise‑reduction tool to capture a one‑ or two‑second profile of the silence, and then reduce the offending noise by about 75 percent throughout the recording. I should stress that this is rarely needed, and it's always a last resort, because such processing can generate swirly, metallic artifacts that draw more attention to themselves than the noise you intended to eliminate! But it's good to listen for such issues with fresh ears at the start of your editing session. If you find yourself using noise‑reduction often, that's a sign that you should find a better place to record, or improve the isolation of the space you've chosen. Don't forget that there are other ways to deal with some noise: often, a high‑pass filter is all you will need to clean up a recording, for example. Also remember that if your recording is to be mixed with music, slight background noise won't be noticeable, and that the more exposed your voice in the end product, the more problematic noise will become.
As I've mentioned, most of our clients prefer to do post‑production work themselves, and request the raw (but edited) recordings. Sometimes, though, as in the Avast! job, the client will want the files ready to go, which might mean using slight EQ and compression. The noise floor on my recordings generally hovers around ‑54dB, but by using EQ to roll off frequencies below 80Hz and above 12kHz, I am usually able to lower the noise floor to around ‑57dB without resorting to noise reduction. Using EQ to reduce low‑end rumble and high‑frequency noise will make your recording sound better, and will be particularly beneficial if you'll be adding compression later, as the compressor's make-up gain won't be raising the level of that noise. Used moderately, compression can usefully reduce dynamic range, and thus improve intelligibility of the words, while still leaving you with a natural‑sounding result. Used excessively, it will suck the life out of a recording.

Perhaps you come from a corporate business background, but you have a remarkable capacity for accents and original character voices, or you’ve been in radio and broadcasting for a number of years. If you’re an actor looking to expand your employment opportunities, mastering voiceover is imperative considering it’s required in every manner of recorded media: film, TV, animation, games, corporate industrials, and commercials. Whatever your specific experience has been to date, getting started in voiceover most often requires the following:
Both union and non-union have advantages and disadvantages; ultimately, it’s a decision that you, as a voice over actor, will have to make. Like everything else, it’s of critical importance that you do your research and weigh up the pros and cons. Seasoned pros will usually tell you it’s best to be a union member because, if you run into trouble, the union will fight your cause.

A demo recording of you doing voice-over work is your CV and your business card combined. If you're applying for a voice-over job, you can send the potential customer your demo via the Internet. Ideally you have multiple demos for different types of gigs. For commercials, clients want to hear 60 to 90 seconds of voice work. If you're auditioning as an audiobook reader, five minutes of demo proves that you can stay in character over a longer stretch of time.
A demo recording of you doing voice-over work is your CV and your business card combined. If you're applying for a voice-over job, you can send the potential customer your demo via the Internet. Ideally you have multiple demos for different types of gigs. For commercials, clients want to hear 60 to 90 seconds of voice work. If you're auditioning as an audiobook reader, five minutes of demo proves that you can stay in character over a longer stretch of time.
A demo recording of you doing voice-over work is your CV and your business card combined. If you're applying for a voice-over job, you can send the potential customer your demo via the Internet. Ideally you have multiple demos for different types of gigs. For commercials, clients want to hear 60 to 90 seconds of voice work. If you're auditioning as an audiobook reader, five minutes of demo proves that you can stay in character over a longer stretch of time.
×